3503A1160KG/020LY | PCBセンサ・オンラインストア東陽テクニカ

Model: 3503A1160KG/020LY
Triaxial MEMS Shock accelerometer, 60kG, thru hole mount, 20-ft integral cable to triple splice assembly with (3) 1-ft 4-cond. cables each with a 8-pin mini DIN (LN), 4-wire bridge

Specifications
アクセサリ
Product Documents

■ Specifications

Performance
Sensitivity (±50 %) (at 10 VDC excitation)	0.0003 mV/(m/s²)	[2]
Sensitivity	0.00003 mV/V/(m/s²)	[3]
Measurement Range	±588400 m/s² pk
Frequency Range (1 dB)	0 to 10000
Resonant Frequency	≥120 kHz
Damping Ratio	2 % Critical	[1]
Non-Linearity (per 10,000 g (98,100 m/s²))	±1 %
Transverse Sensitivity	≤3
Environmental
Overload Limit (Shock)	±784532 m/s² pk	[5]
Overload Limit (Mechanical Stops)	≥782534 m/s² pk
Temperature Range (Storage)	-54 to 121 °C
Temperature Range (Operating)	-54 to 121 °C
Temperature Coefficient of Sensitivity	-0.20 %/°C	[1]
Zero g Offset Temperature Shift	±10 mV	[4]
Base Strain Sensitivity	2.94 (m/s²)/µε	[1]
Electrical
Excitation Voltage (Maximum)	15.0 VDC
Current Consumption	<12 mA
Input Resistance (±700 Ohm)	2000 Ohm	[2]
Output Resistance (±2000 Ohm)	6000 Ohm	[2]
Offset Voltage	-40 to +40 mVDC	[2]
Settling Time	0.01 sec	[6]
Electrical Isolation (Case)	≥10000000 Ohm	[7]
Physical
Sensing Element	Piezoresistive MEMS
Sensing Geometry	Full Active
Housing Material	Titanium
Sealing	Epoxy
Size - Height	6.35 mm
Size - Length	11.81 mm
Size - Width	11.81 mm
Weight (without cable)	2.83 gm	[1]
Electrical Connector	Integral Cable
Electrical Connection Position	Side
Cable Type	8-Cond., shielded, silcone jacket
Cable Termination	Pigtail Ends
Cable Length	3.05 m
Mounting	Through Holes (2)
Mounting Torque	68 to 90 N-cm

All specifications are at room temperature unless otherwise specified.

Product Notes

[1] Typical.
[2] Verified with test data provided on supplied calibration certificate.
[3] Sensitivity is proportional to excitation voltage, and at other excitation values, sensitivity can be predicted from the 10VDC calibrated value with a small (<~.5%) increase in uncertainty.
[4] -65 to +250 °F, ref. 75 °F (-54 to +121 °C, ref. 24 °C)
[5] Half-sine pulse duration, >= 20 µsec.
[6] Settling Time is the maximum time after power-up for the Offset Voltage to be within +/-2% of Measurement Range output of the final offset value. Mounting surface must be at thermal equilibrium.
[7] Individually tested to ensure compliance with specified value.
[8] See PCB Declaration of Conformance PS153 for details.

Accessories:

標準付属アクセサリ

081B114	ワッシャー付きボルト
ACS-62T	校正データ

Optional Versions:

No optional versions